Silverline 930166 TCT Circle Tile Cutter 20 - 94 mm

Product Information

Dremels are handheld power tools with fast-rotating motors. Producing precise cuts is easy with a Dremel due to its small size. Preparing for Cutting Avoid wearing overly bulky knee pads, which may restrict your movement, hindering your performance. Your knee pads should have slip-resistant surfaces so they don’t shift or slide while you’re working. How We Can Help Step 3 – Cut Shape: Position the saw blade at the start of your cutting line and use slow, short cuts to form a starting cut in the tile. Once started, take your time and steadily cut along the line, ensuring the cut stays accurate at all times. Unless you have used an electric tile cutter, once you have cut your tile you will end up with quite a rough edge where the unwanted section has been broken away. Before the cut tile can be used anywhere the edge needs to be tidied up.

Clamp the tile securely in place. Place the tile so that the hole is hanging off the edge of your work surface. Never hold a tile by hand while enlarging a hole with a shaping tool. Due to the high rotational speed of grinders, the risk that the tile will get caught on the shaping tool and spin out of control, potentially injuring you or damaging the tile. Tile pieces half a blade length should be attempted and no more than a quarter of an inch deep. It is possible to cut very clean complex shapes, but patience and care are the key! It is possible to cut a full circle with these nips. Wear knee pads when using a Dremel, grinder, or drill on the floor. The pads will protect and cushion your knees, preventing injuries like knee joint problems, bruises, and stains.

Lower your diamond blade gently toward the tile, and create cuts that cross the center of your hole. Rotate your grinder as needed.

As with every project, as well as having the right tools for the job, it is a really good idea to practice first. Buy an extra box of tiles to practice the cuts, it will pay for itself in the long run. A job done on the cheap is one that will probably have to be done twice!! Create a smaller circle with a hole saw. There’s no need to buy a hole saw in exactly the diameter of hole that you need. Instead, choose a hole saw bit that is slightly smaller than your intended circle. Use a permanent marker to mark the desired outline of your hole or circle. While hole saws only create perfect circles, the shaping tool can turn these into ovals or oblongs. Now that we know what both wet saws and tile cutters are, let’s figure out what the main differences between them are, so you can figure out which one is best for you. Power Needs Step 5 – Tidy Up: Using a tile file or carborundum stone, file off the cut edges of the tile and remove any and all sharp edgesThe key to using these things is to not try and cut too much at once and all of the blade should never be on the tile at once. You need friction to cut a hole in tile, but too much of it produces excess heat. Controlling the heat will help extend your hole saw’s life. Hole saws look like hollow cylinders or empty cups whose rims contain teeth or abrasive materials.Use a saw with a ruby-studded rim if you plan to drill several holes in your tile. A diamond-studded rim is sufficient if you’re cutting a single hole. Two adjustable nozzles spray water from the reservoir onto the blade, but don't worry about overspray; this saw has an excellent water containment system that lets you use it indoors without fear of water splashing everywhere. You can make 22.5 or 45-degree miter cuts, and the edge guide helps you keep your straight cuts perfectly aligned. At 69 pounds, this isn't a light saw, but its included stand makes it convenient to use wherever you need to work.

Porcelain tiles are a lot tougher and more dense than ceramic tiles and this means that they are also much more difficult to cut. Manual snap tile cutters, like rail cutters, have a wheel to score the tile and then rails that apply pressure to snap the tile along the scored line. This type of tile cutting tool is less intimidating for beginners to use but requires more physical exertion and can result in rough cuts that must be sanded. You can only make straight cuts with a rail cutter. Position the saw at a 45-degree angle with the tile. Only one of the saw’s edges should be touching the tile when you start cutting the hole.

Hand tools and power tools usually have rotating or sharp components. Safety gloves will protect your hands from cuts, punctures, and abrasions when you’re using these tools. Safety shoes featuring toe caps will shield your toes from accidental crushing, heavy objects, and impacts during your project. Protect Your Knees That being said, if you plan on tiling your own floors, you are going to need to be able to cut them down to size first. There are two tools that you may use to do so, and these include wet saws and tile cutters. So what exactly are they, and what are the differences between them? Wet Saws and Tile Cutters: The Basics

Grinders will let you get holes started. Then, you can break through your tile and use a shaping tool to smooth and shape the holes. Shaping tools are hand toolsusedfor removingmaterial to make an objecta certain shape.A slightly easier way is by using a mechanical tile cutter or contractors tile cutter as they are sometimes known. This budget wet saw includes a stainless-steel tabletop, blade cooling reservoir to prevent overheating of the 7-inch circular blade (but no water pump), and an adjustable rip fence to ensure straight cuts. A miter gauge also allows bevel cuts up to 45 degrees. This reasonably priced saw is a great tile cutting tool for basic home projects or DIYers. While it can cut a variety of tile types and sizes, you should know that this saw cannot handle tiles as large as many other models. You can only cut a maximum of 12 inches straight, or 7 inches on a diagonal, which means the saw isn't suitable if you need to cut large tiles. The saw weighs a mere 18 pounds. Read on to discover which method is best suited for your purpose. Cutting Circles In Tile With a Hole Saw When it comes to drilling ceramic tiles, first make a mark in the centre of the hole that needs drilling using a hand held tile scribe. Put it in the place where you need the hole and twist it so it scores the glaze. You can then use a power drill (with the hammer action turned off) to drill your hole.