Sonsoke Genshin Impact Anime Figure Zhongli Action Figures Toy Figurine Character Model Toy Statue Figure Cosplay Gift 28cm

Product Information

Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder ( This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.) Initial Layer Height: 0.2 mm ( carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height) Support Roof Pattern: Grid ( this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)

These basic 3D printing settings recommendations for beginners were tested in Slic3r 1.3.0 software. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PetG filaments. Disclaimer : The following printing settings are a recommendation, not an obligation . The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable. Zhongli Genshin figurine for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 28 hours. The figurine’s anatomy and proportions were thoroughly reviewed during the moderation process for the ex-Archon to be depicted harmoniously in the intended dynamic pose. Support Structure: Normal ( you can try using Tree Support Structure if you have difficulty printing any particular assembly part) The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50% .

The model's scale was calculated fromtheapproximate height of Zhongli which is 1880 mm. The 3D printing figurine's chosen scale is 1:8 forthe FFF/FDM versionand 1:16 forthe DLP/SLA/SLS versions. Support Overhang Angle: 60°( this parameter can range from 30° to 70° depending on the part at hand) Flow: 100% ( Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at [email protected]) Support Wall Line Count: 1 ( stronger support that might be more difficult to remove) 0 ( less strong support but is easier to remove) Below you can find printing recommendations for Cura, Simplify3D, Slic3rand PrusaSlicer software. Cura printing recommendations:

Everyone's Favourite Archon Zhongli's New Figurines are Out now. Go grab them now before the stocks runs out!!!

All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed. When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70% . All parts are divided in such a way that you will print them with the smallest number of support structures.

Zhongli figurine for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers. To reduce the amount of filament needed for generated support, we chose the best cutting model. We also hollow parts for you to save resin in the figurine's Eco version. We also give Zhongli's boots, hands, platform's stringers etc... as separate assembly pieces. So you will receive the cleanest results possible. All the assembly parts are STL files in recommended positions that make sure the smoothness of the details surfaces after printing. Therefore, the 3D printing beginners won't face difficulties when placing the parts on a build plate. We cut, keyed and test print the model successfully. Watch the tutorialon how to assemble Zhongli Genshin 3D Printing Figurineon Gambody YouTube channel. You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues.